This "treasure" cold-pressed adhesive has greatly increased the production efficiency of wooden doors and significantly reduced costs!
Dear bosses and production managers of wooden door factories, as well as friends who are currently worried about the pressing board process, are you being overwhelmed by these problems during the pressing board production: long pressing time, slow delivery, and a mountain of orders? The defective rate remains high. Wooden doors crack and show joist marks, and customer complaints keep coming. Workers' efficiency is low, the overall cost is soaring, and the profit margin is severely squeezed. Don't worry. Today, I'm going to share with you a "divine" cold-pressed adhesive that can perfectly solve these problems - the GW-2525 adhesive from Fushen Kuai!
Let me first share a real case with you all. There is a wooden door factory in Shenzhen. Previously, it had been using a certain brand of white latex glue for the pressing board process, but as a result, problems occurred frequently. The pressurization time is ridiculously long, seriously slowing down the operation efficiency. The defect rate during shipment is terrifyingly high. It is not uncommon for wooden doors to crack and have joist marks. The workers showed no enthusiasm for their work, and the overall cost was so high that the boss shook his head. Later, they inquired about the cold pressing process through the Shenzhen sales center of Fushen, and our technicians followed up immediately. After a thorough understanding of the situation, we recommended the GW-2525 adhesive from Fushen Kuai to them. This attempt was truly remarkable!
I. "Rocket-like" improvement in work efficiency
In the cold pressing process, the pressing time of the glue directly determines the production efficiency. The pressurization time for ordinary white latex glue usually takes 4 to 8 hours, and this time cost is simply too high! But the GW-2525 glue from Fushen Kuai is like pressing the "accelerator" for production. Generally, it only takes 30 minutes to use it in the cold pressing process! What does this mean? Efficiency is directly increased by 8 to 10 times! It should be noted that the cold-pressing process has several key requirements for the glue: the open time should be long so that many boards can be coated at one time; The pressurization time should be short for quick delivery. It is also necessary to build up strength quickly to ensure that the wooden door does not crack and has no joist marks. Fushen GW-2525 perfectly meets these demands, making the production process as smooth as flowing water.
Second, say goodbye to cracking and keel marks, with a significant improvement in quality
Fushen GW-2525 has many advantages such as short strength onset time, easy application and thin adhesive amount. After the wooden door factory in Shenzhen switched to this type of glue, the defective rate dropped sharply. All the previous issues of returns and negative reviews caused by cracked wooden doors and joist marks have been resolved. Compared with other glues, its advantages are even more obvious. Ordinary white latex glue is prone to causing deformation of the board and the appearance of keel marks. The panel adhesive not only has a short open time and is troublesome to operate, but also is prone to waste. Urea-formaldehyde glue is not environmentally friendly and is prone to cracking. The Fushen GW-2525 is not only environmentally friendly and does not require glue mixing, but also can achieve no keel marks. Even in a low-temperature environment as low as 5°C, it can still form a film normally. With such quality, anyone who uses it will feel at ease!
Three, efficiency has soared and overall costs have plummeted
Some people might think that such a good glue must be expensive, right? At first, this wooden door factory in Shenzhen thought the same way, believing that the unit price of Fushen GW-2525 seemed a bit higher than the white latex glue they had used before. But our technicians directly gave them a bucket of new glue for a trial. As a result, in an environment with a temperature of around 25 degrees, a bucket of glue was applied to nearly 110 doors and the effect was very good after being pressed for one hour. The on-site boss, upon seeing this, immediately placed an order for 100 barrels (5 tons)! Why so decisive? Just do the math and you'll know! GW-2525 requires less glue application, truly achieving material saving, time saving and labor saving. Excluding the cost savings from reducing the defect rate, just looking at the comprehensive cost and operation efficiency, it directly helped this wooden door factory save more than half of the cost! The efficiency of manual labor has even increased fivefold!
Here is A detailed comparison for everyone (taking Brand A, Brand B and GW-2525 as examples) :
It can be clearly seen from the table that GW-2525 has obvious advantages in all aspects. Less glue application means less material usage, and shorter cold pressing time means higher efficiency. All in all, the cost is naturally lower.
If you are still troubled by the problem of the pressure plate adhesive, don't hesitate any longer! Choosing the GW-2525 adhesive from Fushen Kuai means choosing efficient production, quality assurance and cost control. Hurry up and call [Contact number] or add [wechat contact information] to consult and place an order. Let your wooden door production business take it to the next level!